Verex MONITOR AFx Guida di Installazione Scaricare il pdf (Pagina 2)

21-3691Erev1.3

HSC-IP Module Installation Instructions

9 / 2008

Guardall (formerly VEREX Technology)

5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1

sales@verextech.com +1 905.206.8434 | support@verextech.com +1 905.206.8436 | Fax: +1 905.629.4970

www.guardall.com | +1 877.249.9993

2. Notify the Monitoring Station that you will be installing HSC-IP communications at the customer’s site.

3. Backup the customer’s data base.

If it is an existing customer, obtain their system’s database and save it to the Director Software on a local laptop. It will be

necessary to get the security system’s Unique ID (Keypad Advanced Programming Section S001:02. 1

selection), Third

Party Password (Keypad Advanced Programming Section S001:03.) and the main control unit’s main circuit board’s serial

address number (Keypad Advanced Programming Section S005:10. 1

selection) for your laptop’s Director Software to

communicate with the security system and get the database.

NOTE: Refer to the “Entering and Understanding Advanced Configurations” section at the end of these instructions to learn how to

obtain the above information from the Keypad Advanced Programming Sections.

4. Upgrade the Security System’s main control board’s firmware.

The security system main controller firmware version can be viewed at an LCD keypad connected to it. Use the following

procedure to view the firmware version:

• Logon to the system as a service user. E.g. Default ID:

“000”, service user PIN: “2482” or “7378” if the panel

has communicated with the Director Software.

NOTE: If the system Feature Set (S002È00) is 5 or

greater, keypad programming can not be done. The

menus can only be viewed using the keypad.

Programming can only be done with the Director

Software.

LCD Keypad Screen

Service

Enter PIN: _ _ _ _

• When the control box

tamper is activated, a

service user has

the authority to access system programming.

Menu Options

◄ Config ►

↓Ok

• Using the left and right

arrow screen scrolling

keys on the keypad,

scroll the menus until Config is displayed. Press

Ok.

“Config method” will display. Select “Advanced” with

the arrow keys and press Ok.

S001:00 4-49U42

↓OK ↓ +Group- ↓

• The screen that begins

Advanced programming

will display.

S001:00: this is the start of the System program section.

The code to the right of S001:00 is the firmware version

of the main controller. In this case: “4-49U42“

• The security system main controller firmware must be version 4-49U42 or greater in order to work with the HSC-IP

module.

• If the main controller firmware is a lower version number, it must be upgraded. 4-49 or greater main controller firmware

is available on the version 4.72 or greater Director Software disk. Do e.g. a Direct Connect using a RS485 converter

from the Director Software to the main controller to flash the new firmware to the main controller.

5. Send the database back to the main control board or configure it.

Return the database to an existing customer’s security system or if it is a new system, configure it according to the

customer’s requirements.

6. Basic Programming at the Security System Main Controller to Communicate with the HSC-IP Receiver

• Log on to the Security System Main Controller keypad as a Service User and enter “Advanced” Configurations.

• Refer to the “Entering and Understanding Advanced Configurations” at the end of these instructions for further

information.

• Make the following entries for the security system to communicate with the intended HSC-IP receiver. Use the selections

in the “Default” column.

S005È00 Dialer Selections

Keypad Selections

(left to right on keypad screen) Example:

If the security system has dialer back-up communications, enter the necessary programming selections.

Refer to the Advanced Installation Guide if further dialer programming information is required.

Default Name Selections Description

000000

Dialer Account

Number (Primary)

Enter the dialer account

number.

The monitoring station receiver number that will identify

the security system.

123456·1·0·0·09

ÈSave S005È00

1 2 3 4 5 6 7 ... 12 13

Commenti su questo manuale

Nessun commento

Verex MONITOR AFx Guida di Installazione Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Verex MONITOR AFx