Verex MONITOR AFx Guida di Installazione Scaricare il pdf

21-3691Erev1.3

HSC-IP Module Installation Instructions

9 / 2008

Guardall (formerly VEREX Technology)

5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1

sales@verextech.com +1 905.206.8434 | support@verextech.com +1 905.206.8436 | Fax: +1 905.629.4970

www.guardall.com | +1 877.249.9993

For further information about the HSC-IP Receiver, refer to the HSC-IP Receiver Guide, 21-3690E

For further information about IP, refer to the IP Connectivity Guide, 22-9059E

Introduction

This main control unit HSC-IP Module (part number 650-9062) is the latest version of the previous IP Module (part number

650-9060) and has been designed to communicate with the HSC-IP Receiver over a network or the public internet. For the

ISM/AFx/xL security systems to be able to transmit messages to the HSC-IP Receiver, their main controller HSC-IP Module

must be programmed. A PC software utility to program the HSC-IP Module is used and discussed in these instructions. The

main control unit must have a compatible firmware version to work with the HSC-IP module and will also be discussed in

these instructions. The Director Software can also communicate to a security system through the HSC-IP module over a

network or the public internet and is discussed in these instructions.

Security System Planning for HSC-IP Communications

The following will provide the procedures that are necessary to set-up a security system for communications with a HSC-IP

Receiver and the Director Software.

1. Check List

Considerations to take note of before proceeding with the installation of the Security System HSC-IP Module at a customer’s

site:

NOTE: One Security System HSC-IP Module is used in every main control unit for it to communicate to an HSC-IP

Receiver or Director Software.

• What kind of security system is at the site the HSC-IP communications is intended for? Is it an ISM/AFx/xL system? Only

these types of security systems will work with the HSC-IP Module.

• How many control units are installed at the site? Each control unit will require one HSC-IP Module for it to communicate

with the HSC-IP Receiver or Director Software.

• What is the firmware version of the control units currently in use? The firmware will likely need upgrading to work with the

HSC-IP Module. This is discussed in Step 4.

• What is the main controller serial number? This is a 5 digit number on a sticker on the main controller circuit board.

• Is the customer currently reporting to a monitoring station?

• If “Yes” what is the security system’s account number that reports to the monitoring station?

• What is the type of alarm reporting? Is it by Dialer, DVACS, HSC, MK7?

• Who is the customer’s Internet Service Provider?

• Is there an Ethernet port available at the customer site?

• How are network addresses assigned on the customer LAN? “Static” or “DHCP”.

• Does the customer use Proxy services to access the Internet? If “Yes” what is the Proxy server name? E.g. “NTML”,

“SOCKS5”.

• Does the customer use the Director Software at the site?

Open xL Notices

► These instructions are used for both the Open xL and Monitor xL versions of xL Security Equipment.

► A red dot on xL equipment and its packing material will identify it as the Open xL version.

► Model numbers ending with a “T” will identify the Open xL equipment versions.

► Open xL and Monitor xL versions of xL Security Equipment can not be used together.

► VBUS devices can be used with both Open xL and Monitor xL versions of xL Security Equipment. VBUS devices are not used with ISM

equipment.

► Only Monitor xL Security Equipment can be used to upgrade a Monitor ISM security system. The Open xL version is not used with Monitor ISM

equipment.

► Only Monitor xL Director Software can be used to upgrade Director Software that communicates with a Monitor ISM security system. The Open xL

Director Software is not used with Monitor ISM equipment.

► Open xL, Monitor xL and ISM systems can communicate to the same HSC-IP Receiver. However, the Open xL system will require an Open xL

HSC-IP Module to communicate with the HSC-IP Receiver.

► A regular IP Module (non HSC-IP) can be used by an Open xL, Monitor xL or ISM system if they are only communicating to the Monitor xL or

Open xL Director Software.

► Only Monitor xL Director Software can be used with a Monitor xL Security System.

► Only Open xL Director Software can be used with an Open xL Security System.

► Confirm that the correct firmware is used when upgrading a security system’s firmware. Upgrading an Open xL security system firmware with

Monitor xL firmware can disrupt operations on a system wide scale. An Open xL system must be upgraded with Open xL firmware. The same

applies to only using Monitor xL firmware to upgrade a Monitor xL system.

1 2 3 4 5 6 ... 12 13

Sommario

Pagina 1 - Introduction

Pagina 2 - Save S005È00

Pagina 3 - 9(yes) □ (no)

Pagina 4

Pagina 5 - Connection

Pagina 6

Pagina 7 - PC Utility

Pagina 8 - System Section

Pagina 9 - HSC-IP (SIPII) Section

Pagina 10 - Director Section

Pagina 11 - Communications Status

Pagina 12 - LCD Keypad Screen

Pagina 13

Più documenti per Sistemi di controllo di accesso Verex MONITOR AFx

Per vedere il documento Verex MONITOR AFx Guida Utente

Verex MONITOR AFx Guida Utente (16 pagine)

Verex MONITOR AFx Guida Utente (324 pagine)

Commenti su questo manuale

Nessun commento

Verex MONITOR AFx Guida di Installazione

Navigare online o scaricare Guida di Installazione per Sistemi di controllo di accesso Verex MONITOR AFx. Verex MONITOR AFx Installation guide Manuale Utente

Sommario

Più documenti per Sistemi di controllo di accesso Verex MONITOR AFx

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Verex MONITOR AFx